連線第二個顯示器時如果分辨律發現不對，可以用如下方式設定：

0. 檢視當前的設定

$ xrandr

得到如下結果

Screen 0: minimum 320 x 200, current 2944 x 1080, maximum 8192 x 8192
LVDS-1 connected primary 1920x1080+0+0 (normal left inverted right x axis y axis) 344mm x 194mm
   1920x1080     60.00*+  59.97    59.96    59.93    40.00  
   1680x1050     59.95    59.88  
   160
 
0x1024     60.17  
   1400x1050     59.98  
   1600x900      59.99    59.94    59.95    59.82  
   1280x1024     60.02  
   1440x900      59.89  
   1400x900      59.96    59.88  
   1280x960      60.00  
   1440x810      60.00    59.97  
   1368x768      59.88    59.85  
   1360x768      59.80    59.96  
   1280x800      59.99    59.97
 
    59.81    59.91  
   1152x864      60.00  
   1280x720      60.00    59.99    59.86    59.74  
   1024x768      60.04    60.00  
   960x720       60.00  
   928x696       60.05  
   896x672       60.01  
   1024x576      59.95    59.96    59.90    59.82  
   960x600       59.93    60.00  
   960x540       59.96    59.99    59.63
 
    59.82  
   800x600       60.00    60.32    56.25  
   840x525       60.01    59.88  
   864x486       59.92    59.57  
   800x512       60.17  
   700x525       59.98  
   800x450       59.95    59.82  
   640x512       60.02  
   720x450       59.89  
   700x450       59.96    59.88  
   640x480       60.00    59.94  
   720x405       59.51    58.99  
   684x384       59.88    59.85  
   680x384       59.80    59.96  
   640x400       59.88    59.98  
   576x432       60.06  
   640x360       59.86    59.83    59.84    59.32  
   512x384       60.00  
   512x288       60.00    59.92  
   480x270       59.63    59.82  
   400x300       60.32    56.34  
   432x243       59.92    59.57  
   320x240       60.05  
   360x202       59.51    59.13  
   320x180       59.84    59.32  
VGA-1 connected 1024x768+1920+0 (normal left inverted right x axis y axis) 0mm x 0mm
   1024x768      60.00* 
   800x600       60.32    56.25  
   848x480       60.00  
   640x480       59.94  
LVDS-1-2 disconnected (normal left inverted right x axis y axis)
VGA-1-2 disconnected (normal left inverted right x axis y axis)
HDMI-1-1 disconnected (normal left inverted right x axis y axis)
DP-1-1 disconnected (normal left inverted right x axis y axis)
DP-1-2 disconnected (normal left inverted right x axis y axis)

注意VGA-1就是我們的外接顯示器，當前的分別率是1024x768，而我們需要將其設為1680x1050

1. 得到需要的分辨律的mode, 比如1680 x 1050

$ cvt 1680 1050

得到如下結果

# 1680x1050 59.95 Hz (CVT 1.76MA) hsync: 65.29 kHz; pclk: 146.25 MHz
Modeline "1680x1050_60.00"  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync

2. 新增newmode

$ xrandr --newmode "1680x1050_60.00"  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync

3. 將newmode新增到VGA-1

xrandr --addmode VGA-1 "1680x1050_60.00"

4. 再次檢查VGA設定

$ xrandr

可以看到VGA-1已經有了新設定

VGA-1 connected 1680x1050+1920+0 (normal left inverted right x axis y axis) 0mm x 0mm
   1024x768      60.00  
   800x600       60.32    56.25  
   848x480       60.00  
   640x480       59.94  
   1680x1050_60.00  59.95* 

5. 儲存配置在啟動時自動執行

$ gedit ~/.profile

將第2，3步中的命令加到profile中即可