Centos6.5安裝kvm虛擬化
阿新 • • 發佈:2018-01-28
reat creat text 網絡 橋接 配置 技術 val cati Centos6.5安裝kvm虛擬化
KVM簡介:
1.KVM是開源軟件,全稱是kernel-based virtual machine(基於內核的虛擬機)。
2.是x86架構且硬件支持虛擬化技術(如 intel VT 或 AMD-V)的Linux全虛擬化解決方案。
3.KVM能在不改變linux或windows鏡像的情況下同時運行多個虛擬機,(它的意思是多個虛擬機使用同一鏡像)並為每一個虛擬機配置個性化硬件環境(網卡、磁盤、圖形適配器……)
一、設置虛擬機支持虛擬化
二、先關閉防火墻和selinux
[root@cany ~]# service iptables stop 關閉防火墻 [root@cany ~]# setenforce 0 關閉selinux(臨時生效) setenforce: SELinux is disabled
永久生效方法
[root@cany ~]# vim /etc/sysconfig/selinux SELINUX=enforcing 改為disabled 並reboot生效
三、檢查服務器是否支持虛擬化
[root@cany ~]# grep -E -o ‘vmx|svm‘ /proc/cpuinfo
vmx 如果有輸出VMX就支持虛擬化
四、安裝KVM所需組件,VM使用橋接網絡,使用yum安裝方式(配置好yum源)
[root@cany ~]# yum install -y kvm virt-* libvirts bridge-utils qemu-img
五、加載kvm模塊,查看kvm模塊是否被加載
[root@cany ~]# modprobe kvm-intel
[root@cany ~]# lsmod | grep kvm
kvm_intel 54285 0
kvm 333172 1 kvm_intel 成功加載!
六、配置網卡,具體參數如下
創建橋接網卡命令 : virsh iface-bridge eth0 br0 或者直接編輯網卡配置
[root@cany ~]# virsh iface-bridge eth0 br0 出現下面的錯誤 重啟一下libvirt服務就好了 error: Failed to reconnect to the hypervisor error: no valid connection error: Failed to connect socket to ‘/var/run/libvirt/libvirt-sock‘: No such file or directory [root@cany ~]# /etc/init.d/libvirtd restart Stopping libvirtd daemon: [ OK ] Starting libvirtd daemon: [ OK ] [root@cany ~]# virsh iface-bridge eth0 br0 Created bridge br0 with attached device eth0 Bridge interface br0 started 成功橋接 [root@cany ~]# service network restart 重啟網卡
此時的網卡信息
註意 :因為eth0網卡因為與br0 網卡進行橋接,所以eth0不顯示ip是正常的
七、查看目前所有的網橋接口
[root@cany ~]# brctl show
bridge name bridge id STP enabled interfaces
br0 8000.000c29eb8697 yes eth0
virbr0 8000.525400941201 yes virbr0-nic
八、修改VNC配置
[root@cany ~]# vim /etc/libvirt/qemu.conf
#vnc_listen = "0.0.0.0" 去掉 # 號並wq保存
九、重啟libvirtd和messagebus服務
[root@cany ~]# service libvirtd restart
Stopping libvirtd daemon: [ OK ]
Starting libvirtd daemon: [ OK ]
[root@cany ~]# service messagebus restart
Stopping system message bus: [ OK ]
Starting system message bus: [ OK ]
十、創建、安裝LVM虛擬機
[root@cany ~]# mkdir /abc 創建鏡像存放目錄
[root@cany ~]# mkdir -p /data/kvm 創建虛擬磁盤存放目錄
[root@cany ~]# dd if=/dev/cdrom of=/abc/Centos6.iso 把Centos6.5系統的鏡像文件拷貝到abc目錄下
8726528+0 records in
8726528+0 records out
4467982336 bytes (4.5 GB) copied, 157.25 s, 28.4 MB/s
[root@cany libvirt]# cd /data/kvm/ 進入虛擬磁盤目錄創建img
[root@cany kvm]# qemu-img create -f qcow2 -o preallocation=metadata kvm_cany.img 5G
Formatting ‘kvm_cany.img‘, fmt=qcow2 size=5368709120 encryption=off cluster_size=65536 preallocation=‘metadata‘
[root@cany kvm]# ls
kvm_cany.img
安裝虛擬機
[root@cany kvm]# virt-install --name=kvm_cany --ram 512 --vcpus=1 -f /data/kvm/kvm_cany.img --cdrom=/abc/Centos6.iso --graphics vnc,listen=0.0.0.0,port=7788 --force --autostart
Starting install...
Creating domain... | 0 B 00:00
Cannot open display:
Run ‘virt-viewer --help‘ to see a full list of available command line options
Domain installation still in progress. You can reconnect to
the console to complete the installation process.
如果遇到安裝失敗 請對虛擬磁盤存放目錄權限 chmod -R 777 /data/kvm
VNC客戶端連接KVM虛擬機
軟件:VNC Viewer
VNC連上了之後,安裝系統就ok了!安裝結束後,vnc會自動掛斷,因為此時虛擬機並未啟動!!!
使用 virsh控制臺為 KVM 系統管理若幹任務 下面就讓我們來手動開啟剛剛安裝的KVM虛擬機
[root@cany kvm]# virsh
Welcome to virsh, the virtualization interactive terminal.
Type: ‘help‘ for help with commands
‘quit‘ to quit
virsh # list --all
Id Name State
----------------------------------------------------
- kvm_cany shut off
virsh # start kvm_cany
Domain kvm_cany started
重新使用VNC客戶端進行連接 並對其網卡進行配置
註意:出現網卡重啟失敗的話 將eth0網卡配置文件中的 HWADDR修改成MACADDR
rm -rf /etc/udev/rules.d/70-persistent-net.rules
在虛擬機上查看KVM虛擬機運行狀態
Centos6.5安裝kvm虛擬化