USB Defined Class Codes      

June 15, 2016

原文地址：https://www.usb.org/defined-class-codes  

USB defines class code information that is used to identify a device’s functionality and to nominally load a device driver based on that functionality. The information is contained in three bytes with the names Base Class,SubClass, and Protocol. (Note that ‘Base Class’ is used in this description to identify the first byte of the Class Code triple. That terminology is not used in the USB Specification). There are two places on a device where class code information can be placed.One place is in the Device Descriptor, and the other is in Interface Descriptors.Some defined class codes are allowed to be used only in a Device Descriptor, others can be used in both Device and Interface Descriptors, and some can only be used in Interface Descriptors. The table below shows the currently defined set of Base Class values, what the generic usage is, and where that Base Class can be used (either Device or Interface Descriptors or both).

 

 

Base Class	Descriptor Usage	Description
00h	Device	Use class information in the Interface Descriptors
01h	Interface	Audio
02h	Both	Communications and CDC Control
03h	Interface	HID (Human Interface Device)
05h	Interface	Physical
06h	Interface	Image
07h	Interface	Printer
08h	Interface	Mass Storage
09h	Device	Hub
0Ah	Interface	CDC-Data
0Bh	Interface	Smart Card
0Dh	Interface	Content Security
0Eh	Interface	Video
0Fh	Interface	Personal Healthcare
10h	Interface	Audio/Video Devices
11h	Device	Billboard Device Class
12h	Interface	USB Type-C Bridge Class
DCh	Both	Diagnostic Device
E0h	Interface	Wireless Controller
EFh	Both	Miscellaneous
FEh	Interface	Application Specific
FFh	Both	Vendor Specific

 

 

Base Class 00h (Device)

This base class is defined to be used in Device Descriptors to indicate that class information should be determined from the Interface Descriptors in the device. There is one class code definition in this base class. All other values are reserved.

 

This value is also used in Interface Descriptors to indicate a null class code triple.

 

Base Class	SubClass	Protocol	Meaning
00h	00h	00h	Use class code info from Interface Descriptors

 

 

Base Class 01h (Audio)

This base class is defined for Audio capable devices that conform to the Audio Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.Values outside of that defined spec are reserved. These class codes may only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
01h	xxh	xxh	Audio device

 

 

Base Class 02h (Communications and CDC Control)

 

This base class is defined for devices that conform to the Communications Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved.  Note that the Communication Device Class spec requires some class code values (triples) to be used in Device Descriptors and some to be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
02h	xxh	xxh	Communication device class

 

Base Class 03h (HID – Human Interface Device)

This base class is defined for devices that conform to the HID Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.   Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
03h	xxh	xxh	HID device class

 

Base Class 05h (Physical)

This base class is defined for devices that conform to the Physical Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.  Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
05h	xxh	xxh	Physical device class

 

 

Base Class 06h (Still Imaging)

This base class is defined for devices that conform to the Imaging Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.   Values outside of that defined spec are reserved.

 

Base Class	SubClass	Protocol	Meaning
06h	01h	01h	Still Imaging device

 

 

Base Class 07h (Printer)

This base class is defined for devices that conform to the Printer Device Class Specification found on the USB-IF website.  That specification defines the usable set of SubClass and Protocol values.  Values outside of that defined spec are reserved.  These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
07h	xxh	xxh	Printer device

 

 

Base Class 08h (Mass Storage)

This base class is defined for devices that conform to the Mass Storage Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
08h	xxh	xxh	Mass Storage device

 

 

Base Class 09h (Hub)

This base class is defined for devices that are USB hubs and conform to the definition in the USB specification. That specification defines the complete triples as shown below.  All other values are reserved.  These class codes can only be used in Device Descriptors.

 

Base Class	SubClass	Protocol	Meaning
09h	00h	00h	Full speed Hub
		01h	Hi-speed hub with single TT
		02h	Hi-speed hub with multiple TTs

 

 

Base Class 0Ah (CDC-Data)

This base class is defined for devices that conform to the Communications Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Ah	xxh	xxh	CDC data device

 

 

Base Class 0Bh (Smart Card)

This base class is defined for devices that conform to the Smart Card Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Bh	xxh	xxh	Smart Card device

 

 

Base Class 0Dh (Content Security)

This base class is defined for devices that conform to the Content Security Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Dh	00h	00h	Content Security device

 

 

Base Class 0Eh (Video)

This base class is defined for devices that conform to the Video Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Eh	xxh	xxh	Video device

 

 

Base Class 0Fh (Personal Healthcare)

This base class is defined for devices that conform to the Personal Healthcare Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes should only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Fh	xxh	xxh	Personal Healthcare device

 

 

Base Class 10h (Audio/Video Devices)

The USB Audio/Video (AV) Device Class Definition describes the methods used to communicate with devices or functions embedded in composite devices that are used to manipulate audio, video, voice, and all image- and sound-related functionality. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors. 

 

Base Class	SubClass	Protocol	Meaning
10h	01h   02h   03h	00h	Audio/Video Device – AVControl Interface
		00h	Audio/Video Device – AVData Video Streaming Interface
		00h	Audio/Video Device – AVData Audio Streaming Interface

 

 

 

Base Class 11h (Billboard Device)

This base class is defined for devices that conform to the Billboard Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Device Descriptors.

 

Base Class	SubClass	Protocol	Meaning
11h	00h	00h	Billboard Device

 

 

Base Class 12h (USB Type-C Bridge Device)

This base class is defined for devices that conform to the USB Type-C Bridge Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
12h	00h	00h	USB Type-C Bridge Device

 

 

 

 

Base Class DCh (Diagnostic Device)

This base class is defined for devices that diagnostic devices. This class code can be used in Device or Interface Descriptors. 
Trace is a form of debugging where processor or system activity is made externally visible in real-time or stored and later retrieved for viewing by an applications developer, applications program, or, external equipment specializing observing system activity. 
Design for Debug or Test (Dfx). This refers to a logic block that provides debug or test support (E.g. via Test Access Port (TAP)). 
DvC:  Debug Capability on the USB device (Device Capability) 

 

Base Class	SubClass	Protocol	Meaning
DCh	01h	01h	USB2 Compliance Device.  Definition for this device can be found at http://www.intel.com/technology/usb/spec.htm
	02h	00h	Debug Target vendor defined. Please seehttp://www.intel.com/content/www/us/en/io/universal-serial-bus/extensible-host-controler-interface-usb-xhci.html for more info.
		01h	GNU Remote Debug Command Set. Please seehttp://www.intel.com/content/www/us/en/io/universal-serial-bus/extensible-host-controler-interface-usb-xhci.html for more info.
	03h	00h	Undefined
		01h	Vendor defined Trace protocol on DbC.
	04h	00h	Undefined
		01h	Vendor defined Dfx protocol on DbC.
	05h	00h	Vendor defined Trace protocol over General Purpose (GP) endpoint on DvC.
		01h	GNU Protocol protocol over General Purpose (GP) endpoint on DvC. http://www.gnu.org/software/gdb/
	06h	00h	Undefined
		01h	Vendor defined Dfx protocol on DvC.
	07h	00h	Undefined
		01h	Vendor defined Trace protocol on DvC.
	08h	00h	Undefined

 

 

Base Class E0h (Wireless Controller)

This base class is defined for devices that are Wireless controllers. Values not shown in the table below are reserved. These class codes are to be used in Interface Descriptors, with the exception of the Bluetooth class code which can also be used in a Device Descriptor. 

 

 

Base Class	SubClass	Protocol	Meaning
E0h	01h	01h	Bluetooth Programming Interface.  Get specific information fromwww.bluetooth.com.
		02h	UWB Radio Control Interface.  Definition for this is found in the Wireless USB Specification in Chapter 8.
		03h	Remote NDIS.  Information can be found at:http://www.microsoft.com/windowsmobile/mobileoperators/default.mspx
		04h	Bluetooth AMP Controller. Get specific information fromwww.bluetooth.com.
	2h	01h	Host Wire Adapter Control/Data interface.  Definition can be found in the Wireless USB Specification in Chapter 8.
		02h	Device Wire Adapter Control/Data interface.  Definition can be found in the Wireless USB Specification in Chapter 8.
		03h	Device Wire Adapter Isochronous interface.  Definition can be found in the Wireless USB Specification in Chapter 8.

 

Base Class EFh (Miscellaneous)

This base class is defined for miscellaneous device definitions. Values not shown in the table below are reserved. The use of these class codes (Device or Interface descriptor) are specifically annotated in each entry below.

 

 

 

Base Class	SubClass	Protocol	Meaning
EFh	01h	01h	Active Sync device. This class code can be used in either Device or Interface Descriptors. Contact Microsoft for more information on this class.
		02h	Palm Sync. This class code can be used in either Device or Interface Descriptors.
	02h	01h	Interface Association Descriptor. The usage of this class code triple is defined in the Interface Association Descriptor ECN that is provided on www.usb.org . This class code may only be used in Device Descriptors.
		02h	Wire Adapter Multifunction Peripheral programming interface. Definition can be found in the Wireless USB Specification in Chapter 8. This class code may only be used in Device Descriptors
	03h	01h	Cable Based Association Framework. This is defined in the Association Model addendum to the Wireless USB specification. This class code may only be used in Interface Descriptors.
	04h	01h	RNDIS over Ethernet. Connecting a host to the Internet via Ethernet mobile device. The device appears to the host as an Ethernet gateway device. This class code may only be used in Interface Descriptors.
		02h	RNDIS over WiFi. Connecting a host to the Internet via WiFi enabled mobile device.  The device represents itself to the host as an 802.11 compliant network device. This class code may only be used in Interface Descriptors.
		03h	RNDIS over WiMAX Connecting a host to the Internet via WiMAX enabled mobile device.  The device is represented to the host as an 802.16 network device. This class code may only be used in Interface Descriptors.
		04h	RNDIS over WWAN Connecting a host to the Internet via a device using mobile broadband, i.e. WWAN (GSM/CDMA). This class code may only be used in Interface Descriptors.
		05h	RNDIS for Raw IPv4 Connecting a host to the Internet using raw IPv4 via non-Ethernet mobile device.  Devices that provide raw IPv4, not in an Ethernet packet, may use this form to in lieu of other stock types. This class code may only be used in Interface Descriptors.
		06h	RNDIS for Raw IPv6 Connecting a host to the Internet using raw IPv6 via non-Ethernet mobile device.  Devices that provide raw IPv6, not in an Ethernet packet, may use this form to in lieu of other stock types. This class code may only be used in Interface Descriptors.
		07h	RNDIS for GPRS Connecting a host to the Internet over GPRS mobile device using the device’s cellular radio
	05h	00h	USB3 Vision Control Interface	Machine Vision Device conforming to the USB3 Vision specification. This standard covers cameras and other related devices that are typically used in machine vision, industrial, and embedded applications. Reference: http://visiononline.org/ This class code may only be used in Interface Descriptors.
		01h	USB3 Vision Event Interface
		02h	USB3 Vision Streaming Interface
	06h	01h	STEP. Stream Transport Efficient Protocol for content protection.
		02h	STEP RAW. Stream Transport Efficient Protocol for Raw content protection.
	07h	01h	Command Interface in IAD	The DVB Common Interface (DVB-CI) specification describes a system whereby a removable CI Conditional Access Module (CICAM), given the appropriate usage rights, unscrambles protected pay-TV content and routes it over the same interface back to a TV receiver for display. An interface association for a DVB-CI function will contain a DVB-CI Command Interface for command, control, and status information, it may contain a DVB-CI Media Interface for audiovisual data streams, and it may also contain a CDC EEM interface to provide bridged networking to the CICAM. Reference: https://www.dvb.org/standards/dvb-ci-plus
		01h	Command Interface in Interface Descriptor
		02h	Media Interface in Interface Descriptor

 

 

 

 

 

 

 

Base Class FEh (Application Specific)

This base class is defined for devices that conform to several class specifications found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.  Values outside of that defined spec are reserved.  These class codes can only be used in Interface Descriptors.

 

 

Base Class

SubClass

Protocol 相關推薦 USB Defined Class Codes   USB Defined Class Codes       June 15, 2016 原文地址：https://www.usb.org/defined-class-codes   USB defin 第十八篇:融匯貫通--談USB Video Class驅動 USB Video Class驅動是WINDOWS系統包含的一個針對於USB VIDEO 類的驅動程式. 好多project師都做過USB VIDEO裝置端的開發, 基本的工作內容為: 使用FIRMWARE,或者LIINUX GADGET驅動程式, 構建USB VIDEO裝置 USB Video Class Specification 筆記 關於USB Class 將裝置歸為既定的類別，並對相應類別的裝置的在USB協議的應用級協議和介面作出規範，這樣只要按照類裝置的標準實現驅動程式和裝置，則一套驅動可以驅動這一類的所有裝置，而這一類裝置可以在已經包含這一類裝置驅動程式的作業系統中實現“免驅”。比較常見的類裝置是 Spring Boot - Error creating bean with name 'dataSource' defined in class path resource 刪除 需要 reat text class with config autoconf ext 看起來像最初的問題是與自動配置。 如果你不需要數據源，只需從自動配置過程中刪除它： @EnableAutoConfiguration(exclude={DataSour spring AOP使用中Error creating bean with name ‘…’defined in class path resource..問題及其解決方法 factory fail 正常 ins aspect 工作內容 thread def before spring AOP使用中Error creating bean with name ‘…’defined in class path resource..問題及其解決方法 Spring Boot 報錯：Error creating bean with name 'entityManagerFactory' defined in class path resource fine 依賴 debug isp jpa java idt .com ima spring boot 寫一個web項目，在使用spring-data-jpa的時候，啟動報如下錯誤： Error starting ApplicationContext. To display idea報錯 Error creating bean with name 'requestMappingHandlerMapping' defined in class path resource ror factory pojo mapped clas mes del strong per 核對一下控制器是不是寫了相同的路徑。。。org.springframework.beans.factory.BeanCreationException: Error crea Cannot find class [org.apache.commons.dbcp.BasicDataSource] for bean with name 'dataSource' defined in class path resource [applicationContext Cannot find class [org.apache.commons.dbcp.BasicDataSource] for bean with name 'dataSource' defined in class path resource [applicationContext.xml]; 該錯誤是因 Error creating bean with name 'dataSource' defined in class path resource [spring-config.xml]: BeanP 錯誤描述： org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'dataSource' defined in class path resource [spring-con Cannot find class [org.apache.commons.dbcp.BasicDataSource] for bean with name 'dataSource' defined 這個錯誤搞了我半天，上網查詢都說是沒匯入commons dbcp和commons pool的jar 包導致的，可是我都匯入了呀，後來看到一篇帖子，也遇到了同樣的錯誤。 解決方法：匯入commons-dbcp.jar和commons-pool.jar包 注意：在解決這個問題時，我在官網上htt 報錯org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'sessionFactory' defined in class path resource [bean 報這種錯的原因基本上是applicationContext.xml檔案中bean配置錯誤，錯誤如下： org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'sessionFactory' 【SSH】Error creating bean with name 'sessionFactory' defined in class path resource [applicationConte   今天在小鹹兒再一次學習SSH的時候，在進行使用者名稱校驗的時候，啟動專案報了一個曾經遇到的錯誤：   Error creating bean with name ‘sessionFactory’ defined in class path resource [applic Error creating bean with name 'client' defined in class path resource [conf/vcollab-es.xml] Caused by: org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'client' defined in class path resource [conf/vcolla The bean 'counterFactory', defined in class path resource [org/springframework/cloud/netflix/zuul/Zu SpringCloud啟動zuul時，報如下錯誤： 查詢發現是Springboot的版本問題，我這裡springbood版本是2.1.0，SpringCloud是F版本。把SpringBoot版本降到2.0.6即可。 2018-11-29 15:54:38.127 INFO 3 spring-data-jpa Error creating bean with name 'entityManagerFactory' defined in class path resource 專案地址:https://github.com/heng1234/springdata-jpa 問題描述：   剛開始實體類程式碼是這樣寫的 package com.hvly.springjp_1.com.hlvy.entity; import lombok.Data Error creating bean with name 'accounterService' defined in class path resource.... 如果用Spring框架是出現下面的錯誤: 原因: 在pom.xml中少匯入spring-aspects-4.2.4.RELEASE.jar包了,直接匯入就可以了 在pom.xml新增下面的jar座標就可以了       &nbs Error creating bean with name 'methodValidationPostProcessor' defined in class path resource 異常：Error creating bean with name ‘methodValidationPostProcessor’ defined in class path resource [org/springframework/boot/autoconfi Cannot refer to a non-final variable xx inside an inner class defined in a different method的原因 今天遇到一個小問題，下面是網上摘抄的解釋： 為了說明這個問題，先得明白說明是區域性內部類，區域性內部類就是在外部類的方法中定義的類。那麼標題中的錯誤指的是，內部類不能引用該方法中非 final 修飾的變數。 那麼為什麼呢? 因為生命週期的原因。方法中的區域性變數，方法結 A bean with that name has already been defined in DataSourceConfiguration$Hikari.class 問題： 啟動SpringBoot專案報錯： *************************** APPLICATION FAILED TO START *********************** Spring Cloud Finchley.RELEASE 使用 gateway Error creating bean with name 'webHandler' defined in class pom <dependency> <groupId>org.springframework.cloud</groupId> <artifactId>spring-cloud-starter-gatewa