【PLC】三菱PLC控制元件 PLCActiveXEnvironment3.0
ErrorCode[錯誤程式碼]
0x01802007
| Transfer setting[傳輸設定] |
| Receive data error [接收資料錯誤] The data received is abnormal. [接收到的資料不正常] The corrective action is as follows: [糾正措施如下：] Review the system, e.g. PLC CPU, module setting and cable status. [ 檢視PLC系統，例如 PLC CPU，模組設定和電纜狀態。] Check the cable. [檢查電纜。] Exit the program and restart the IBM-PC/AT compatible. [退出程式並重啟計算機。] |
| <ErrorCode:1802007 [HEX]> |
0x01808003
| Transfer setting[傳輸設定] |
| Driver not yet started [驅動程式尚未啟動] The corrective action is as follows: [糾正措施如下：] The network board driver is not started. [網路板驅動程式未啟動] Start the driver. [啟用驅動] |
| <ErrorCode:1808003 [HEX]> |
0x01808009
| Transfer setting[傳輸設定] |
| COM port handle error [COM埠控制代碼錯誤] The handle of the COM port cannot be acquired. [無法獲取COM埠的控制代碼。] The COM port object cannot be copied. [無法複製COM埠物件。] The SOCKET object cannot be copied. [無法複製SOCKET物件。] The corrective action is as follows: [糾正措施如下：] Check for an application which uses the COM port. [檢測是否有程式佔用了COM埠] Exit the program and restart the IBM-PC/AT compatible. [退出程式並重啟計算機。] |
| <ErrorCode:1808009 [HEX]> |
0x0180800e
| Transfer setting[傳輸設定] |
| Shared memory open error [共享記憶體開啟錯誤] Open processing of shared memory failed. [共享記憶體的開放處理失敗。] The corrective action is follows: [糾正措施如下：] Check whether the GX Simulator has started. [檢查GX Simulator是否已啟動。] Exit the program and restart the IBM-PC/AT compatible. [退出程式並重啟計算機。] |
| <ErrorCode:180800e [HEX]> |
0x01808201
| Transfer setting[傳輸設定] |
| Send error [傳送錯誤] Data send failed. [資料傳送失敗] The corrective action is as follows. [糾正措施如下：] Review the system, e.g. PLC CPU, module setting and cable status. [ 檢視PLC系統，例如 PLC CPU，模組設定和電纜狀態。] Make COM port setting on the control panel of the OS. [在作業系統的控制面板上進行COM埠設定。] Make Ethernet board and protocol settings on the control panel. [在控制面板上進行乙太網板和協議設定。] Retry the method. [重試此方法。] Exit the program and restart the IBM-PC/AT compatible. [退出程式並重啟計算機。] |
| <ErrorCode:1808201[HEX]> |
0x01808301
| Transfer setting[傳輸設定] |
| Receive error [接收錯誤] Data receive failed. [資料接收失敗] The corrective action is follows: [糾正措施如下：] Review the system, e.g. PLC CPU, module setting and cable status. [ 檢視PLC系統，例如 PLC CPU，模組設定和電纜狀態。] Review the time-out value of the property. [檢查屬性的超時值。] Review the time-out value on the communication settings utility. [檢視通訊設定實用程式的超時值。] Retry the method. [重試此方法。] Exit the program and restart the IBM-PC/AT compatible. [退出程式並重啟計算機。] |
| <ErrorCode:1808301 [HEX]> |
0x0180840a
| Transfer setting[傳輸設定] |
| Communication control setting error [通訊控制設定錯誤] The control value of the property is unauthorised. [Control的屬性值不在設定範圍內。] The corrective action is as follows: [糾正措施如下：] Review the control value of the property. [檢查Control的屬性值。] Set it again on the communication settings utility. [在communication settings設定區域重新設定。] |
| <ErrorCode:180840a [HEX]> |
0x0180840b
| Transfer setting[傳輸設定] |
| Time-out error [超時錯誤] Though the time-out period had elapsed, data could not be received. [雖然超時時間已過，但無法接收資料。] The corrective action is as follows: [糾正措施如下：] Review the time-out value of the property. [檢測time out 的屬性值] Set it again on the communication settings utility. [在communication settings設定區域重新設定。] Review the system, e.g. PLC CPU, module setting and cable status. [ 檢視PLC系統，例如 PLC CPU，模組設定和電纜狀態。] Retry the method. [重試此方法。] Perform Close once and execute Open again. [執行一次關閉然後再次開啟。] Exit the program and restart the IBM-PC/AT compatible. [退出程式並重啟計算機。] |
| <ErrorCode:180840b[HEX]> |
0x01808502
| Transfer setting[傳輸設定] |
| USB driver connect error [USB驅動程式連線錯誤] Connection of the USB driver failed. [連線USB驅動程式失敗。] The corrective action is as follows: [糾正措施如下：] Exit the program and restart the IBM-PC/AT compatible. [退出程式並重啟計算機。] Reinstall MX Component. [重灌MX Component ] |
| <ErrorCode:1808502 [HEX]> |
0x04000001
| Transfer setting[傳輸設定] |
| No command error [沒有命令錯誤] The specified CPU type cannot be used to perform processing. [指定的CPU型別不能用於執行處理。] The corrective action is as follows: [糾正措施如下：] Check the CPU type set to ActCpuType. [檢查設定為ActCpuType的CPU型別。] Check whether the system configuration is supported or not. [檢查是否支援系統配置。] Exit the program and restart the IBM-PC/AT compatible. [退出程式並重啟計算機。] Reinstall MX Component. [重灌MX Component ] Set it again on the communication settings utility. [在communication settings設定區域重新設定。] |
| <ErrorCode:4000001 [HEX]> |
0xf2100004
| Transfer setting[傳輸設定] |
| There is no response from the modem. [調變解調器沒有響應。] Causes can be the following: [原因可能如下：] Abnormality in the modem. [調變解調器的異常。] Telephone number setting mistake. [電話號碼設定錯誤。] The corrective action is follows: [糾正措施如下：] Check the status of the modem. [檢查調變解調器的狀態。] Check the telephone number. [檢查電話號碼。] If the problem persists even after checking the above points, change the value of the properties set (Properties such as ActConnectionCDWaitTime etc., which set the timings) in case of program settings type and change the contents of the detailed settings that were set using the wizard in case of utility settings type. [如果在檢查上述點後問題仍然存在，則在程式設定型別的情況下更改屬性集的值（ActConnectionCDWaitTime等屬性，設定時間），並更改使用該設定設定的詳細設定的內容。 實用程式設定型別的嚮導。] Exit the program and restart the IBM-PC/AT compatible. [退出程式並重啟計算機。] |
| <ErrorCode:f2100004 [HEX]> |
0xf2000006
| Transfer setting[傳輸設定] |
| The PC modem did not receive the AT command. [PC調變解調器沒有收到AT命令。] Causes can be the following: [原因可能如下。] Invalid AT command was specified. [指定了無效的AT命令。] Abnormality in the modem. [調變解調器的異常。] The corrective action is follows: [糾正措施如下：] Check the contents of the AT Command. [檢查AT命令的內容。] Check the status of the modem. [檢查調變解調器的狀態。] |
| <ErrorCode:f2000004 [HEX]> |
PLC Monitor Utility引數設定儲存位置
C:\MELSEC\Act\Utl\ ActMon.exe
Regedit[登錄檔]-x64
| 計算機\HKEY_LOCAL_MACHINE\SOFTWARE\WOW6432Node\MITSUBISHI\SWnD5-ACT\MONUTL\LogicalSt\STECMOPEN |
Regedit[登錄檔]-x86
| HKEY_LOCAL_MACHINE\SOFTWARE\MITSUBISHI\SWnD5-ACT\MONUTL\LogicalSt\STECMOPEN |
FX3UC
Communication setting[串列埠通訊設定]
CPU type[CPU型別]
| Item |
HEX |
DEC |
| Q00J |
0x0030 |
48 |
| Q00 |
0x0031 |
49 |
| Q01 |
0x0032 |
50 |
| Q02(H) |
0x0022 |
34 |
| Q06H |
0x0023 |
35 |
| Q12H |
0x0024 |
36 |
| Q25H |
0x0025 |
37 |
| Q12PH |
0x0041 |
65 |
| Q25PH |
0x0042 |
66 |
| Q12PRH |
0x0043 |
67 |
| Q25PRH |
0x0044 |
68 |
| Q02(H)-A |
0x0141 |
321 |
| Q06H-A |
0x0142 |
322 |
| Q2A |
0x0011 |
17 |
| Q2AS(H) |
0x0011 |
17 |
| Q2AS1 |
0x0012 |
18 |
| Q2AS(H)S1 |
0x0012 |
18 |
| Q3A |
0x0013 |
19 |
| Q4A |
0x0014 |
20 |
| Q4AR |
0x0014 |
20 |
| A0J2H |
0x0102 |
258 |
| A1FX |
0x0103 |
259 |
| A1S |
0x0104 |
260 |
| A1S(S1) |
0x0104 |
260 |
| A1SJ |
0x0104 |
260 |
| A1SH |
0x0105 |
261 |
| A1SJH |
0x0105 |
261 |
| A1N |
0x0106 |
262 |
| A2C |
0x0107 |
263 |
| A2CJ |
0x0107 |
263 |
| A2N(S1) |
0x0108 |
264 |
| A2S |
0x0108 |
264 |
| A2S(S1) |
0x0108 |
264 |
| A2SH |
0x0109 |
265 |
| A2SH(S1) |
0x0109 |
265 |
| A3N |
0x010A |
266 |
| A2A(S1) |
0x010C |
268 |
| A3A |
0x010D |
269 |
| A2U(S1) |
0x010E |
270 |
| A2US(S1) |
0x010E |
270 |
| A2AS(S1) |
0x010E |
270 |
| A2AS-S30 |
0x0110 |
272 |
| A2AS-S60 |
0x0110 |
272 |
| A2USH-S1 |
0x010F |
271 |
| A3U |
0x0110 |
272 |
| A4U |
0x0111 |
273 |
| A171SH |
0x0601 |
1537 |
| A172SH |
0x0602 |
1538 |
| A173UH(S1) |
0x0604 |
1540 |
| A273UH(S3) |
0x0603 |
1539 |
| FX0(S) |
0x0201 |
513 |
| FX0N |
0x0202 |
514 |
| FX1 |
0x0203 |
515 |
| FX1S |
0x0206 |
518 |
| FX1N(C) |
0x0207 |
519 |
| FX2(C) |
0x0204 |
516 |
| FXU/FX2C |
0x0204 |
516 |
| FX2N(C) |
0x0205 |
517 |
| FX3UC |
0x0208 |
520 |
Transmission speed [傳輸速率]
| Item |
HEX |
DEC |
| 9600 |
0x00002580 |
9600 |
| 19200 |
0x00004b00 |
19200 |
| 38400 |
0x00009600 |
38400 |
| 57600 |
0x0000e100 |
57600 |
| 115200 |
0x0001c200 |
115200 |
Control[控制方式]
| Item |
HEX |
DEC |
| DTR Control |
0x0001 |
1 |
| RTS Control |
0x0002 |
2 |
| DTR and RTS Control |
0x0007 |
7 |
| DTR or RTS Control |
0x0008 |
8 |