利用uboot啟動遠端Kernel(TFTP)以及掛載遠端ROOTFS(NFS)
阿新 • • 發佈：2019-01-16
Welcome to minicom 2.5
OPTIONS: I18n
Compiled on May 2 2011, 00:39:27.
Port /dev/ttyS0
Press CTRL-A Z for help on special keys
OKOK
U-Boot 2013.01-rc2 (Jan 07 2013 - 10:18:16) for FriendlyLEG-TINY210
CPU:
Board: FriendlyLEG-TINY210
DRAM: 512 MiB
WARNING: Caches not enabled
PWM Moudle Initialized.
GPD0CON : 1111, GPD0DAT : e
NAND: 2048 MiB
MMC: SAMSUNG SD/MMC: 0, SAMSUNG SD/MMC: 1
In: serial
Out: serial
Err: serial
Net: dm9000
Hit any key to stop autoboot: 0
dm9000 i/o: 0x88001000, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 00:40:5c:26:0a:5b
operating at 100M full duplex mode
Using dm9000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.80
Filename 'uImage'.
Load address: 0x21000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#############################################
done
Bytes transferred = 3555936 (364260 hex)
## Booting kernel from Legacy Image at 21000000 ...
Image Name: Linux-3.0.8-TINY210V2+
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3555872 Bytes = 3.4 MiB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0.8-TINY210V2+ (
[ 0.000000] CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: MINI210
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU S5PV210/S5PC110 (id 0x43110220)
[ 0.000000] s5pv210_init_clocks: initializing clocks
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] s5pv210_setup_clocks: registering clocks
[ 0.000000] s5pv210_setup_clocks: clkdiv0 = 14131440, clkdiv1 = 00000400
[ 0.000000] s5pv210_setup_clocks: xtal is 24000000
[ 0.000000] S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000 V=54000000
[ 0.000000] S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000
[ 0.000000] HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
[ 0.000000] sclk_dmc: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk_onenand: source is hclk_dsys (1), rate is 166750000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 66700000
[ 0.000000] sclk_mixer: source is sclk_dac (0), rate is 54000000
[ 0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_cam0: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_cam1: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_fimd: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 47642857
[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 47642857
[ 0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000
[ 0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000
[ 0.000000] sclk_mfc: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk_g2d: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk_g3d: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk_csis: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_pwi: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000
[ 0.000000] s5p: 36864 kbytes system memory reserved for mfc at 0x3dbf5000, 0-bank base(0x3dbf5000)
[ 0.000000] s5p: 36864 kbytes system memory reserved for mfc at 0x3b7f5000, 1-bank base(0x00000000)
[ 0.000000] s5p: 6144 kbytes system memory reserved for fimc0 at 0x3b1f5000, 1-bank base(0x00000000)
[ 0.000000] s5p: 16 kbytes system memory reserved for fimc1 at 0x3b1f1000, 1-bank base(0x00000000)
[ 0.000000] s5p: 6144 kbytes system memory reserved for fimc2 at 0x3abf1000, 1-bank base(0x00000000)
[ 0.000000] s5p: 8192 kbytes system memory reserved for jpeg at 0x3a3f1000, 0-bank base(0x3a3f1000)
[ 0.000000] s5p: 13060 kbytes system memory reserved for fimd at 0x39730000, 1-bank base(0x00000000)
[ 0.000000] s5p: 8192 kbytes system memory reserved for g2d at 0x38f30000, 0-bank base(0x38f30000)
[ 0.000000] On node 0 totalpages: 102203
[ 0.000000] Normal zone: 1024 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 101179 pages, LIFO batch:31
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 101179
[ 0.000000] Kernel command line: root=/dev/nfs rw nfsroot=192.168.1.5:/opt/S5PV210/rootfs,nolock,tcp ip=192.168.1.80 console=ttySAC0,115200 ctp=1 kgdboc=ttySAC0,115200
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 399MB 0MB = 399MB total
[ 0.000000] Memory: 396940k/512416k available, 11872k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)
[ 0.000000] vmalloc : 0xe0800000 - 0xfd000000 ( 456 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc002d000 ( 148 kB)
[ 0.000000] .text : 0xc002d000 - 0xc06911ec (6545 kB)
[ 0.000000] .data : 0xc0692000 - 0xc06d9c40 ( 288 kB)
[ 0.000000] .bss : 0xc06d9c64 - 0xc071e000 ( 273 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:393
[ 0.000000] VIC @fd000000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd010000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd020000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd030000: id 0x00041192, vendor 0x41
[ 0.000000] mult[140737]
[ 0.000000] max_delta_ns[2937815369]
[ 0.000000] min_delta_ns[30517]
[ 0.000000] rate[32768]
[ 0.000000] HZ[256]
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttySAC0] enabled
[ 0.491824] Calibrating delay loop... 994.84 BogoMIPS (lpj=1941504)
[ 0.515576] pid_max: default: 32768 minimum: 301
[ 0.515827] Mount-cache hash table entries: 512
[ 0.516312] Initializing cgroup subsys debug
[ 0.516362] Initializing cgroup subsys cpuacct
[ 0.516419] Initializing cgroup subsys freezer
[ 0.520295] CPU: Testing write buffer coherency: ok
[ 0.530660] print_constraints: dummy:
[ 0.530949] NET: Registered protocol family 16
[ 0.549032] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.565355] fimd at 0x39730000
[ 0.565467] hsmmc0: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.565534] hsmmc1: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.565594] hsmmc2: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.565654] hsmmc3: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.573248] S5PV210: Initializing architecture
[ 0.577794] s3c-adc s5pv210-adc: attached adc driver
[ 0.581035] s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0
[ 0.590202] print_constraints: pd_tv_supply: 5000 mV normal
[ 0.595088] print_constraints: pd_lcd_supply: 5000 mV normal
[ 0.600797] print_constraints: pd_g3d_supply: 5000 mV normal
[ 0.606515] print_constraints: pd_mfc_supply: 5000 mV normal
[ 0.612256] print_constraints: pd_audio_supply: 5000 mV normal
[ 0.679867] bio: create slab <bio-0> at 0
[ 0.682650] SCSI subsystem initialized
[ 0.688076] usbcore: registered new interface driver usbfs
[ 0.688866] usbcore: registered new interface driver hub
[ 0.689384] usbcore: registered new device driver usb
[ 0.690919] s3c-i2c s3c2440-i2c.0: slave address 0x10
[ 0.690978] s3c-i2c s3c2440-i2c.0: bus frequency set to 378 KHz
[ 0.694312] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.698209] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 0.703096] s3c-i2c s3c2440-i2c.1: bus frequency set to 65 KHz
[ 0.709538] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.714317] s3c-i2c s3c2440-i2c.2: slave address 0x10
[ 0.719208] s3c-i2c s3c2440-i2c.2: bus frequency set to 260 KHz
[ 0.726196] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 0.732195] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.737949] Bluetooth: Core ver 2.16
[ 0.740770] NET: Registered protocol family 31
[ 0.744847] Bluetooth: HCI device and connection manager initialized
[ 0.751091] Bluetooth: HCI socket layer initialized
[ 0.755912] Bluetooth: L2CAP socket layer initialized
[ 0.760971] Bluetooth: SCO socket layer initialized
[ 0.766890] cfg80211: Calling CRDA to update world regulatory domain
[ 0.773644] Switching to clocksource clock_source_systimer
[ 0.781205] Switched to NOHz mode on CPU #0
[ 0.814450] NET: Registered protocol family 2
[ 0.814719] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.815436] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.815751] TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
[ 0.817762] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.823843] TCP reno registered
[ 0.826926] UDP hash table entries: 256 (order: 1, 12288 bytes)
[ 0.832817] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[ 0.839450] NET: Registered protocol family 1
[ 0.843904] RPC: Registered named UNIX socket transport module.
[ 0.849390] RPC: Registered udp transport module.
[ 0.854022] RPC: Registered tcp transport module.
[ 0.858686] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.865330] PMU: registered new PMU device of type 0
[ 0.870717] cpuidle: phy_regs_save:0x389ff000
[ 0.874682] Loaded driver for PL330 DMAC-0 s3c-pl330
[ 0.879385] DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
[ 0.885545] Loaded driver for PL330 DMAC-1 s3c-pl330
[ 0.890354] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.896527] Loaded driver for PL330 DMAC-2 s3c-pl330
[ 0.901343] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.916582] ashmem: initialized
[ 0.948580] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 0.949199] yaffs: yaffs built Jan 21 2013 17:12:49 Installing.
[ 0.949318] msgmni has been set to 775
[ 0.952233] io scheduler noop registered
[ 0.952280] io scheduler deadline registered
[ 0.952505] io scheduler cfq registered (default)
[ 0.953022] start plist test
[ 0.964738] end plist test
[ 0.965544] s3cfb s3cfb: win 2: pmem_start=0x39b95000
[ 0.965600] s3cfb s3cfb: [fb2] dma: 0x39b95000, cpu: 0xe1000000, size: 0x0085c000
[ 0.980388] FIMD src sclk = 166750000
[ 0.980503] s3cfb s3cfb: registered successfully
[ 0.999445] s5pv210-uart.0: ttySAC0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
[ 1.004497] s5pv210-uart.1: ttySAC1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
[ 1.012278] s5pv210-uart.2: ttySAC2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
[ 1.020063] s5pv210-uart.3: ttySAC3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
[ 1.028139] kgdb: Registered I/O driver kgdboc.
[ 1.029336] leds initialized
[ 1.029853] pwm initialized
[ 1.030397] mini210-adc initialized
[ 1.031294] backlight initialized
[ 1.033368] PA FB = 0x39B95000, bits per pixel = 32
[ 1.033419] screen width=800 height=480 va=0xd9b95000 pa=0x39b95000
[ 1.037300] xres_virtual = 800, yres_virtual = 1440, xoffset = 0, yoffset = 0
[ 1.044271] fb_size=8765440
[ 1.046967] Back frameBuffer[0].VAddr=d9d0c000 PAddr=39d0c000 size=1536000
[ 1.053883] Back frameBuffer[1].VAddr=d9e83000 PAddr=39e83000 size=1536000
[ 1.060711] Video Y Buffer[0].VAddr=d9ffa000 PAddr=39ffa000 size=921600
[ 1.067274] Video Y Buffer[1].VAddr=da0db000 PAddr=3a0db000 size=921600
[ 1.073853] Video Y Buffer[2].VAddr=da1bc000 PAddr=3a1bc000 size=921600
[ 1.080435] Video UV Buffer[0].VAddr=da29d000 PAddr=3a29d000 size=462848
[ 1.087114] Video UV Buffer[1].VAddr=da30e000 PAddr=3a30e000 size=462848
[ 1.093781] Video UV Buffer[2].VAddr=da37f000 PAddr=3a37f000 size=462848
[ 1.116968] brd: module loaded
[ 1.125950] loop: module loaded
[ 1.129049] S3C NAND Driver, (c) 2008 Samsung Electronics
[ 1.232765] MLC nand initialized, 2012 ported by FriendlyARM
[ 1.232829] S3C NAND Driver is using hardware ECC.
[ 1.232908] NAND device: Manufacturer ID: 0xec, Chip ID: 0xd5 (Samsung NAND 2GiB 3,3V 8-bit)
[ 1.232996] Creating 5 MTD partitions on "s5pv210-nand":
[ 1.234619] 0x0000000c0000-0x000000100000 : "misc"
[ 1.241942] 0x000000100000-0x000000600000 : "recovery"
[ 1.247967] 0x000000600000-0x000000b00000 : "kernel"
[ 1.252719] 0x000000b00000-0x000000e00000 : "ramdisk"
[ 1.257397] 0x000000e00000-0x000080000000 : "system"
[ 1.599156] PPP generic driver version 2.4.2
[ 1.600049] PPP Deflate Compression module registered
[ 1.600107] PPP BSD Compression module registered
[ 1.601243] PPP MPPE Compression module registered
[ 1.601298] NET: Registered protocol family 24
[ 1.601345] tun: Universal TUN/TAP device driver, 1.6
[ 1.605267] tun: (C) 1999-2004 Max Krasnyansky <
[ 1.611828] dm9000 Ethernet Driver, V1.31
[ 1.616853] eth0: dm9000a at e0838000,e083c00c IRQ 39 MAC: 00:40:5c:26:0a:5b (chip)
[ 1.623722] usbcore: registered new interface driver ath9k_htc
[ 1.629099] sdhci: Secure Digital Host Controller Interface driver
[ 1.634953] sdhci: Copyright(c) Pierre Ossman
[ 1.639317] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)
[ 1.645807] s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
[ 1.652605] mmc0: no vmmc regulator found
[ 1.656922] Registered led device: mmc0::
[ 1.661006] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[ 1.667701] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133400000 Hz)
[ 1.674146] s3c-sdhci s3c-sdhci.1: clock source 2: sclk_mmc (47642857 Hz)
[ 1.682986] mmc1: no vmmc regulator found
[ 1.685346] Registered led device: mmc1::
[ 1.689318] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
[ 1.699252] s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133400000 Hz)
[ 1.702486] s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)
[ 1.709288] mmc2: no vmmc regulator found
[ 1.715636] Registered led device: mmc2::
[ 1.717615] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[ 1.724348] s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz)
[ 1.730824] s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)
[ 1.740810] mmc3: no vmmc regulator found
[ 1.741967] Registered led device: mmc3::
[ 1.746035] mmc3: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
[ 1.752951] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.761432] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[ 1.764380] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 1.771406] s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
[ 1.789533] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[ 1.790770] hub 1-0:1.0: USB hub found
[ 1.790847] hub 1-0:1.0: 1 port detected
[ 1.791927] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.798054] s5p-ohci s5p-ohci: EXYNOS OHCI Host Controller
[ 1.801174] s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
[ 1.808229] s5p-ohci s5p-ohci: irq 87, io mem 0xec300000
[ 1.872876] hub 2-0:1.0: USB hub found
[ 1.872960] hub 2-0:1.0: 1 port detected
[ 1.874844] usbcore: registered new interface driver usbserial
[ 1.874907] usbserial: USB Serial Driver core
[ 1.874948] Initializing USB Mass Storage driver...
[ 1.878576] usbcore: registered new interface driver usb-storage
[ 1.879346] USB Mass Storage support registered.
[ 1.884519] s3c-udc : S3C HS USB Device Controller Driver, (c) 2008-2009 Samsung Electronics
[ 1.884530] s3c-udc : version 15 March 2009 (DMA Mode)
[ 1.906446] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.906517] android_usb gadget: Number of LUNs=1
[ 1.908906] lun0: LUN: removable file: (no medium)
[ 1.917974] android_usb gadget: android_usb ready
[ 1.935143] Registered gadget driver 'android_usb'
[ 1.936127] mousedev: PS/2 mouse device common for all mice
[ 1.937682] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 1.939892] touchscreen-1wire initialized
[ 1.939941] backlight-1wire initialized
[ 1.943390] setup_irq: ret = 0
[ 1.949344] PWM clock = 66700000
[ 1.949382] TCNT_FOR_SAMPLE_BIT = 433, TCFG1 = 00010000
[ 1.955703] input: fa_ts_input as /devices/virtual/input/input1
[ 1.962284] ts-if initialized
[ 1.964422] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[ 1.969103] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 1.976461] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 1.979792] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 1.985189] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 1.990673] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 2.000583] using rtc device, s3c, for alarms
[ 2.000695] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[ 2.007003] i2c /dev entries driver
[ 2.012407] Linux video capture interface: v2.00
[ 2.014907] gspca: v2.13.0 registered
[ 2.018650] usbcore: registered new interface driver zc3xx
[ 2.023604] mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics
[ 2.023610]
[ 2.035622] S3C JPEG Driver, (c) 2007 Samsung Electronics
[ 2.037195] JPEG driver for S5PV210
[ 2.041789] i2c i2c-1: attached s5p_ddc into i2c adapter successfully
[ 2.047438] S5PC11X HPD Driver, (c) 2010 Samsung Electronics
[ 2.053696] S5PC11X CEC Driver, (c) 2010 Samsung Electronics
[ 2.060876] usbcore: registered new interface driver uvcvideo
[ 2.064060] USB Video Class driver (v1.1.0)
[ 2.110690] input: mma7660 as /devices/platform/s3c2440-i2c.0/i2c-0/0-004c/input/input2
[ 2.111368] mma7660 0-004c: MMA7660 device is probed successfully.
[ 2.111789] i2c-core: driver [mma7660] using legacy suspend method
[ 2.111853] i2c-core: driver [mma7660] using legacy resume method
[ 2.114800] MMA7660 sensor driver registered.
[ 2.119136] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[ 2.125786] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
[ 2.134915] device-mapper: uevent: version 1.0.3
[ 2.138459] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected]
[ 2.145779] Bluetooth: HCI UART driver ver 2.2
[ 2.150063] Bluetooth: HCI H4 protocol initialized
[ 2.154842] Bluetooth: HCI BCSP protocol initialized
[ 2.159764] Bluetooth: HCILL protocol initialized
[ 2.164444] Bluetooth: HCIATH3K protocol initialized
[ 2.169384] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 2.175389] usbcore: registered new interface driver btusb
[ 2.180717] cpuidle: using governor ladder
[ 2.185080] cpuidle: using governor menu
[ 2.208617] usbcore: registered new interface driver usbhid
[ 2.208677] usbhid: USB HID core driver
[ 2.211671] ALSA device list:
[ 2.211711] No soundcards found.
[ 2.211742] oprofile: hardware counters not available
[ 2.211784] oprofile: using timer interrupt.
[ 2.214112] TCP cubic registered
[ 2.216531] NET: Registered protocol family 17
[ 2.220996] NET: Registered protocol family 15
[ 2.225725] Bluetooth: RFCOMM TTY layer initialized
[ 2.230259] Bluetooth: RFCOMM socket layer initialized
[ 2.235331] Bluetooth: RFCOMM ver 1.11
[ 2.239059] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.244356] Bluetooth: BNEP filters: protocol multicast
[ 2.249546] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.255892] NET: Registered protocol family 35
[ 2.260125] lib80211: common routines for IEEE802.11 drivers
[ 2.265489] lib80211_crypt: registered algorithm 'NULL'
[ 2.270687] Registering the dns_resolver key type
[ 2.275418] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 2.282994] ThumbEE CPU extension supported.
[ 2.287734] s5pv210_cpufreq_init: S5PV210 cpu-freq driver
[ 2.294262] regulator_init_complete: pd_mfc_supply: disabling
[ 2.298338] regulator_init_complete: pd_tv_supply: disabling
[ 2.304023] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 2.309451] s3c-rtc s3c64xx-rtc: setting system clock to 2013-01-23 10:13:49 UTC (1358936029)
[ 2.323559] FIMC0 registered successfully
[ 2.325558] FIMC1 registered successfully
[ 2.327653] FIMC2 registered successfully
[ 2.330330] S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
[ 2.336619] s5p-tvout s5p-tvout: hpd status is cable removed
[ 2.371581] usb 1-1: new high speed USB device number 2 using s5p-ehci
[ 2.383306] dm9000 dm9000: eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
[ 2.398891] IP-Config: Guessing netmask 255.255.255.0
[ 2.399198] IP-Config: Complete:
[ 2.399239] device=eth0, addr=192.168.1.80, mask=255.255.255.0, gw=255.255.255.255,
[ 2.399315] host=192.168.1.80, domain=, nis-domain=(none),
[ 2.399365] bootserver=255.255.255.255, rootserver=192.168.1.5, rootpath=
[ 2.502828] hub 1-1:1.0: USB hub found
[ 2.503021] hub 1-1:1.0: 4 ports detected
[ 2.653901] VFS: Mounted root (nfs filesystem) on device 0:13.
[ 2.654047] Freeing init memory: 148K
[ 5.735512] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
Please press Enter to activate this console.
[ 6.200469] udevd[876]: starting version 175
[[email protected] /]#
[ 12.817109] vo_open::check tvout start !!
[ 12.821308] vo_open::check tvout start !!
相關推薦
利用uboot啟動遠端Kernel(TFTP)以及掛載遠端ROOTFS(NFS)
[email protected]:/tmp# minicom /dev/ttyS0 Welcome to minicom 2.5 OPTIONS: I18n Compiled on May 2 2011, 00:39:27. Port /dev/ttyS0 Press CTRL-A Z fo
配置pycharm專業版同步修改遠端伺服器程式碼以及使用遠端直譯器除錯
配置pycharm同步修改遠端伺服器程式碼以及使用遠端直譯器除錯 場景： 假如你的程式碼需要在伺服器上執行，程式碼是python寫的，那麼你想編寫以及除錯程式碼，如果用虛擬機器或者xshell連線後的vim編輯，顯然極不方便，哪怕你裝了豪華版的vim，或者線上jupyter編輯,但是
[uboot] uboot啟動kernel篇（一）——Legacy-uImage & FIT-uImage
轉自https://blog.csdn.net/ooonebook/article/details/53495002 一、uImage 編譯kernel之後，會生成Image或者壓縮過的zImage。但是這兩種映象的格式並沒有辦法提供給uboot的足夠的資訊來進行load、jump或者驗證操
[uboot] uboot啟動kernel篇（一）——Legacy-uImage & FIT-uImage
一、uImage 編譯kernel之後，會生成Image或者壓縮過的zImage。但是這兩種映象的格式並沒有辦法提供給uboot的足夠的資訊來進行load、jump或者驗證操作等等。因此，uboot提供了mkimage工具，來將kernel製作為uboot可以識別的格式
[uboot] uboot啟動kernel篇（三）——uboot解析uImage的kernel資訊
一、說明 從《[uboot] （番外篇）uboot啟動kernel篇（二）——bootm跳轉到kernel的流程》我們知道了bootm的過程中，從uImage解析出kernel資訊主要是在bootm_find_os中實現的。 這裡注意，這些資訊主要是在mkimage
Beaglebone Black——理論篇beaglebone black啟動——從串列埠獲得SPL、U-BOOT，TFTP伺服器獲得核心，NFS伺服器掛載根檔案系統
一般來講啟動一個系統所需的bootloader（SPL/MLO、u-boot.img）和根檔案系統（/boot下包含核心zImage）要麼是放在NAND Flash，或者是SD卡，或者是eMMC，或者是USB中，那麼還有一種方式，就是所需要的這些檔案全部
關於uboot啟動核心停留在Starting Kernel問題的解決
當通過Kermit方式使用串列埠線上將核心uImage載入到記憶體0xC0008000地址處後，執行bootm c0008000命令去啟動核心，console控制檯資訊執行到Starting Kernel就卡住不動了，這句列印資訊是uboot的最後一條列印資訊，也就是我
CentOS6啟動流程呢個以及刪除boot分區相關實驗
同步數據 app 超級 config c# status sim 重啟 b- centos6啟動流程 主動讀取BIOS，通過CMOS加載硬件信息 ，並進行POST，指定第一個可啟動的設備 ROM：BIOS，Basic Input and Output System，保
關於Resin在Eclipse或者Myeclipse上利用Debug模式部署的方法以及遇到的一些問題
引用 目錄 pca source 添加 -i beans 解決辦法 center 本文轉自：http://blog.csdn.net/yangvip101/article/details/47310985 最近新跳槽了家公司，以前的公司一直用Tomcat而新公司卻用的是re
第1階段——uboot啟動函數bootm命令分析(9)
lean bank phy arm img 1.2 ota 缺省 過程 本節主要學習: 詳細分析UBOOT中"bootcmd=nand read.jffs2 0x30007FC0 kernel;bootm 0x30007FC0"中怎麽實現bootm命令啟動內核. 其中b
在不重啟的情況下新增一塊磁盤中出現的問題以及掛載到對應的目錄下的詳細解決方法
不重啟 情況下 新增一塊 在vm中添加一塊新磁盤：[[email protected] ~]# fdisk -l 進行掃描，但找不到新增的磁盤解決方法：[[email protected] ~]# ls /sys/class/scsi_host/ 查看總線主機號 [
好系統U盤啟動盤的用處以及制作方法
情況下 all 教程 簡單 color ges win 系統文件 主板 U盤是我們在工作和生活中的好幫手，能儲存和傳遞數據文件，但如果你僅知道U盤的這些用處，那就有些大材小用了。其實U盤還有很多其它用處，U盤啟動盤就是其中非常重要的一種。好系統U盤啟動盤主要是用來修復和重裝
一，移植uboot，分析uboot啟動流程
寫到 位置 ESS fff setup boa soft bec 進入 文檔時間：2018-08-08 交叉編譯器：arm-linux-gcc-4.3.2 Ubuntu版本：16.04 uboot版本：2013.10 uboot啟動流程簡要如下： a,設置CPU為管
Linux 關於安裝rabbitmq以及開啟遠端訪問許可權步驟
時光飛逝，距離上次寫部落格居然已經兩個月之久，近期因為專案進度緊，而一直沒有抽出時間來進行總結，本人會在近期將專案中所涉及到的技術以及一些操作進行總結並更新到部落格中，今天我們就來聊聊linux下安裝rabbitmq的安裝步驟。 本篇部落格主要以安裝步驟為主，所以並不會涉及到太
阿里雲CentOS7.3RPM方式安裝MySQL以及配置遠端連線
1. 下載Mysql安裝包 2. 解除安裝阿里映象自帶的MariaDB資料庫 3. 解壓安裝下載的Mysql資料庫 *4. 環境配置 1.下載MySQL安裝包 https://dev.mysql.com/downloads/ 官方網址，根據自己需求
kernel版本以及版本含義
mainline mainline指由Linus Torvalds親自制作的核心釋出版，是官方當前最新版本的kernel source。在Torvalds對所有其他程式設計師所做出的重大變化進行整合，並且對先前版本的bug進行幾輪修復之後，大約每十週正式釋出一個新版本。mainline事實上
[uboot] （第五章）uboot流程——uboot啟動流程
轉自https://blog.csdn.net/ooonebook/article/details/53070065 以下例子都以project X專案tiny210（s5pv210平臺,armv7架構）為例 [uboot] uboot流程系列： [project
[uboot] （第六章）uboot流程——命令列模式以及命令處理介紹
轉自https://blog.csdn.net/ooonebook/article/details/53164198 以下例子都以project X專案tiny210（s5pv210平臺,armv7架構）為例 [uboot] uboot流程系列： [project
Linux下磁碟分割槽，格式化以及掛載
接下來，我們詳細介紹在Linux下，如何用命令對磁碟進分割槽、格式化以及如何掛載到目錄。 測試環境：VMware Workstation / centos7 操作步驟： 第一步：首先來看看當前虛擬機器的磁碟情況。 以及先前分割槽情況：由下
centOS7.3新安裝後，設定IP，以及Putty遠端和Xshell遠端 （學習是個持續的過程，也許中途放鬆過，但是仍然能重新撿起來，並學以致用，方為真勇士）
有一段時間沒有寫學習心得了；現在開始加油，再接再勵。 從最基礎的開始 1.安裝centOS7.3之後設定IP地址。一般linux的系統都是作為伺服器的系統來使用，伺服器的屬性註定了他的IP不能隨意的更變，所以需要設定一個固定的IP地址。 一般centos系統安裝完成後，IP都是通過dhcp來獲得的。所以