APC-UPS產品設定ip地址&設定輸出電壓
阿新 • • 發佈：2019-02-19
使用AP963,AP9631之前，必須設定一些基本引數。本文介紹瞭如何通過串列埠通訊方式配置AP9630，AP9631.
配置步驟如下：
使用940-0299通訊線進行配置：
1．使用940-0299通訊線（網路管理卡附帶）連線執行終端模擬程式的計算機和UPS。
2．如該計算機的串列埠（連線940-0299通訊線）正被APC軟體PowerChute Business Edition或其他程式使用，請關閉相關程式。 啟動終端模擬程式如HyperTerminal，設定串列埠引數為：9600bps, No Parity , 8 data bits , 1 stop bit , and No Flow Control
注：修改串列埠引數後，要斷開並重新連線該會話(connection)之後，設定方生效。
3. 確認上述兩步無誤後，按回車鍵。
4. 輸入 User Name及 Password ，其預設設定均為 apc。
5. 正確登入後，網路管理卡的管理介面將自動彈出。
User Name : apc
Password : ***
American Power Conversion Network Management Card AOS v5.0.1
(c) Copyright 2008 All Rights Reserved Smart-UPS & Matrix-UPS APP v5.0.0
-------------------------------------------------------------------------------
Name : Unknown Date : 02/11/2009
Contact : Unknown Time : 02:13:46
Location : Unknown User : Administrator
Up Time : 0 Days 4 Hours 29 Minutes Stat : P+ N+ A+
apc>?
Network Management Card Commands:
---------------------------------------------------------------------------
? about alarmcount boot cd date
delete dir eventlog exit format ftp
help ping portspeed prompt quit radius
reboot resetToDef system tcpip user web
xferINI xferStatus
Device Commands:
---------------------------------------------------------------------------
ups
apc>tcpip ?
Usage: tcpip -- Configure and display Tcpip parameters
tcpip [-i <ip address>]
[-s <subnet mask>]
[-g <gateway>]
[-d <domain name>]
[-h <host name>]
apc>tcpip -i 10.219.10.237
E000: Success
Reboot required for change to take effect
apc>tcpip -s 255.255.254.0
E000: Success
Reboot required for change to take effect
apc>tcpip -g 10.210.10.1
E000: Success
Reboot required for change to take effect
apc>tcpip
E000: Success
IP Address: 10.219.10.237
MAC Address: 00 C0 B7 D6 D9 E7
Subnet Mask: 255.255.254.0
Gateway: 10.219.10.1
Domain Name: example.com
Host Name: APC
使用940-0299通訊線進行配置：
1．使用940-0299通訊線（網路管理卡附帶）連線執行終端模擬程式的計算機和UPS。
2．如該計算機的串列埠（連線940-0299通訊線）正被APC軟體PowerChute Business Edition或其他程式使用，請關閉相關程式。 啟動終端模擬程式如HyperTerminal，設定串列埠引數為：9600bps, No Parity , 8 data bits , 1 stop bit , and No Flow Control
注：修改串列埠引數後，要斷開並重新連線該會話(connection)之後，設定方生效。
3. 確認上述兩步無誤後，按回車鍵。
4. 輸入 User Name及 Password ，其預設設定均為 apc。
5. 正確登入後，網路管理卡的管理介面將自動彈出。
User Name : apc
Password : ***
American Power Conversion Network Management Card AOS v5.0.1
(c) Copyright 2008 All Rights Reserved Smart-UPS & Matrix-UPS APP v5.0.0
-------------------------------------------------------------------------------
Name : Unknown Date : 02/11/2009
Contact : Unknown Time : 02:13:46
Location : Unknown User : Administrator
Up Time : 0 Days 4 Hours 29 Minutes Stat : P+ N+ A+
apc>?
Network Management Card Commands:
---------------------------------------------------------------------------
? about alarmcount boot cd date
delete dir eventlog exit format ftp
help ping portspeed prompt quit radius
reboot resetToDef system tcpip user web
xferINI xferStatus
Device Commands:
---------------------------------------------------------------------------
ups
apc>tcpip ?
Usage: tcpip -- Configure and display Tcpip parameters
tcpip [-i <ip address>]
[-s <subnet mask>]
[-g <gateway>]
[-d <domain name>]
[-h <host name>]
apc>tcpip -i 10.219.10.237
E000: Success
Reboot required for change to take effect
apc>tcpip -s 255.255.254.0
E000: Success
Reboot required for change to take effect
apc>tcpip -g 10.210.10.1
E000: Success
Reboot required for change to take effect
apc>tcpip
E000: Success
IP Address: 10.219.10.237
MAC Address: 00 C0 B7 D6 D9 E7
Subnet Mask: 255.255.254.0
Gateway: 10.219.10.1
Domain Name: example.com
Host Name: APC