[email protected]:~$ sudo '/usr/local/ezsdk/setup.sh'  [sudo] password for eagle:  -------------------------------------------------------------------------------- TISDK setup script This script will set up your development host for sdkdevelopment. Parts of this script require administrator priviliges (sudoaccess). -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Verifying Linux host distribution Ubuntu 10.04 LTS found successfully, continuing.. -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will make sure you have the proper host supportpackages installed using the following command: sudoapt-get install xinetd tftpd nfs-kernel-serverminicom build-essential libncurses5-dev

uboot-mkimage autoconf automake Note! This command requires you to have administratorpriviliges (sudo access)  on your host. Press return to continue 正在讀取軟體包列表... 完成 正在分析軟體包的依賴關係樹       正在讀取狀態資訊... 完成       xinetd 已經是最新的版本了。 tftpd 已經是最新的版本了。 nfs-kernel-server 已經是最新的版本了。 minicom 已經是最新的版本了。 build-essential 已經是最新的版本了。 libncurses5-dev 已經是最新的版本了。 uboot-mkimage 已經是最新的版本了。 autoconf 已經是最新的版本了。 automake 已經是最新的版本了。 automake 被設定為手動安裝。 升級了 0 個軟體包，新安裝了 0 個軟體包，要解除安裝 0 個軟體包，有 223 個軟體包未被升級。 Package verification and installation successfullycompleted -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- In which directory do you want to install the targetfilesystem?(if this directory does not exist it will becreated) Ensure that complete path is provided, otherwise NFS path inbootargs might be incomplete [ /home/eagle/targetfs ]     -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will extract the target filesystem to/home/eagle/targetfs #根檔案系統的路徑：/home/eagle/targetfs Note! This command requires you to have administratorpriviliges (sudo access)  on your host. Press return to continue /home/eagle/targetfs already exists (r) rename existing filesystem (o) overwrite existingfilesystem (s) skip filesystem extraction [r] o Old /home/eagle/targetfs removed Successfully extracted ezsdk-dm816x-evm-rootfs.tar.gz to/home/eagle/targetfs -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will update the EXEC_DIR variables in the Rules.make file This will facilitate the SDK to install (with make install)rebuilt binaries in    /home/eagle/targetfs/home/root/dm816x-evm The files will be available from /home/root/dm816x-evm on thetarget. This setting can be changed later by editing Rules.make andchanging the EXEC_DIR variable. Press return to continueRules.make edited successfully.. -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will export your target filesystem for NFSaccess. Note! This command requires you to have administratorpriviliges (sudo access)  on your host. Press return to continue  * Stopping NFS kernel daemon                                    [ OK ]   * Unexporting directories for NFS kerneldaemon...                   [ OK ]   * Exporting directories for NFS kerneldaemon...                     [ OK]   * Starting NFS kernel daemon                                    [ OK ]  -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Which directory do you want to be your tftp root directory?(if this directory does notexist it will be created for you) [ /tftpboot]  -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will set up the tftp server in the /tftpbootdirectory. Note! This command requires you to have administratorpriviliges (sudo access)  on your host. Press return to continue Successfully copied uImage-dm816x-evm.bin to tftp root directory/tftpboot #編譯好的核心映象檔案路徑：/tftpboot /etc/xinetd.d/tftp successfullycreated Restarting tftp server  * Stopping internet superserver xinetd                            [ OK ]   * Starting internet superserver xinetd                            [ OK ]  -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will set up minicom (serial communicationapplication) for SDK development For boards that contain a USB-to-Serial converter on the board(BeagleBone),  the port used for minicom will be automatically detected. Bydefault Ubuntu  will not recognize this device. Setup will add will add a udevrule to  /etc/udev/ so that from now on it will be recognized as soonas the board is  plugged in. For other boards, the serial will defualt to /dev/ttyS0.Please update based  on your setup. -------------------------------------------------------------------------------- NOTE: For boards with a built-in USB to Serial adapter pleasepress       ENTERat the prompt below.  The correct port will bedetermined      automatically at a later step.  For all otherboards select       theserial port that the board is connected to Which serial port do you want to use with minicom? [ /dev/ttyS0]  Configuration saved to /home/eagle/.minirc.dfl. You can changeit further from inside minicom, see the Software Development Guide for moreinformation. -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- This step will set up the u-boot variables for booting theEVM. Autodetected the following ip address of your host, correct itif necessary [  ]  Select Linux kernel location:  1: TFTP  2: SD card [ 1 ]  Select root file system location:  1: NFS  2: SD card [ 1 ]  Available kernel images in /tftproot:    uImage-dm816x-evm.bin Which kernel image do you want to boot from TFTP? [ uImage-dm816x-evm.bin]  Resulting u-boot variable settings: setenv bootdelay 4 setenv baudrate 115200 setenv bootargs console=ttyO2,115200n8 rootwait [email protected] [email protected] vmalloc=500Mnotifyk.vpssm3_sva=0xBF900000 root=/dev/nfsnfsroot=:/home/eagle/targetfs ip=dhcp setenv bootcmd 'dhcp;setenv serverip ;tftpboot;bootm' setenv autoload no setenv serverip setenv bootfile uImage-dm816x-evm.bin -------------------------------------------------------------------------------- Would you like to create a minicom script with the aboveparameters (y/n)? [ y ]  Successfully wrote setup_uimage-tftp_fs-nfs.minicom Would you like to run the setup script now (y/n)? Thisrequires you to connect the RS-232 cable between your host and EVM as well as yourethernet cable as described in the Quick Start Guide. Please ensure that SW4switch for NAND is in ON position. Once answering 'y' on the prompt below you will have 300seconds to connect the board and power cycle it before the setup times out After successfully executing this script, your EVM will be setup. You will be  able to connect to it by executing 'minicom -w' or if youprefer a windows host you can set up Tera Term as explained in the SoftwareDeveloper's Guide. If you connect minicom or Tera Term and power cycle the boardLinux will boot. [ y ] /usr/local/ezsdk ~ Welcome to minicom 2.4 OPTIONS: I18n  Compiled on Jan 25 2010, 06:49:09. Port /dev/ttyS0 Press CTRL-A Z for help on special keys  CTRL-A Z for help |115200 8N1 | NOR |Minicom 2.4    | VT102 | Online00:14        You can manually run minicom in the future with this setupscript using: minicom -S setup_uimage-tftp_fs-nfs.minicom -------------------------------------------------------------------------------- TISDK setup completed! Please continue reading the Software Developer's Guide formore information on how to develop software on the EVM